Кошик
287 відгуків
+380 (96) 365-09-25
+380 (44) 221-98-89
Яргу

Драйвер крокового двигуна SEA2D34 (3 ампери)

1 215 ₴

  • В наявності
Драйвер крокового двигуна SEA2D34 (3 ампери)
Драйвер крокового двигуна SEA2D34 (3 ампери)В наявності
1 215 ₴
+380 (96) 365-09-25
Дмитро
  • +380 (44) 221-98-89
+380 (96) 365-09-25
Дмитро
  • +380 (44) 221-98-89
повернення товару протягом 14 днів за домовленістю
У компанії підключені електронні платежі. Тепер ви можете купити будь-який товар не покидаючи сайту.
  • Висока продуктивність, чудова стабільність
  • Спеціальний ланцюг керування неабияк знижує шум і збільшує стабільність обертання
  • Селектор мікрокроків 12/8. Максимальна роздільна здатність 40000 steps/rev
  • Струм котушки автоматично скорочується наполовину, коли імпульс зупиняється вище 100 мс
  • Частота відгуку до 200Kpps
  • Захист від помилок: перегрівання, перевантаження за струмом, низької напруги
  • Оптичний ізольований вхідний/вихідний сигнал
  • Двополюсний режим переривання струму забезпечує більшу швидкість і потужність
  • Діапазон струму збудження: 0.1A ~ 3.0A
  • Один вхідний діапазон потужності: DC12-40V (найкращий вхід: DC36V)
  • Малий об'єм: 136 × 92 × 25 (мм), вага: 0.3kg

SEA2D34 є високопродуктивним цифровим мікрокроковим драйвером із постійним кутом і крутним моментом, напругою DC12-40V, з одним джерелом живлення. Він відповідає 2-фазним кроковим двигунам із струмом до 3,0 А, розміром 57-86 мм і 6 або 8-дротовим.

Режим біполярного постійного струму, що застосовується всередині, забезпечує плавність роботи двигуна та невеликий шум. Підвищення напруги покращує швидкодію двигуна та крутний момент на виході. Струм котушки автоматично скорочується наполовину та зменшує перегрівання, коли імпульс зупиняється вище 100 мс. Користувачі застосовують низьку швидкість і високий підрозділ за низької частоти пульсу, це може бути до 12800 кроків/оберт, що покращує точність роботи та зменшує вібрацію.

Mark

Function

Instruction

POWER

Power indicator

Power on, the green indicator normally on.

TM

Working indicator light

When the pulse frequency is low, the green indicator flashes, when the pulse frequency is high, the green indicator normally on.

O.H

Overheat indicator

The Temperature rise exceeds 70 ℃, the red indicator normally on.

O.C

Overcurrent / Low voltage indicator

The current exceeds rated value or the voltage is lower than rated value, the red indicator normally on.

Im

Phase current setting adjuster

Set the phase current, clockwise it increases, anticlockwise it dereases.

+

Input signal positive side

Pulse signal power supply should in the range of +5V~+24V, if higher than +5V , needs to add a resistor on PU-, DR-, FM- ( do not add on + sides ).

PU

Pulse signal

When the falling edge is valid, the motor moves a step as the pulse become lower, input resistance is 220Ω;. Requires: low level +0V~+0.5V, high level +4V~+5V, pulse width >2.5&μs.

DR

Direction control signal

For changing the direction,input resistance is 220Ω;. Requires: low level +0V~+0.5V, high level+4V~+5V, pulse width >2.5μs.

MF

Motor free signal

When the low electrical level is valid, it cuts off the motor current, the driver stops working and motor will be in a free state.

+V

Power+

DC12~40V ( the optimal voltage is DC36V )

-V

Power-

AC、BC

Connect to the motor

Please refer to the motor connections.

+A、-A

+B、-B

1. Please do not reverse the power supply, input voltage not more than DC40V;

2. The input control signal level is +5V, if higher than +5V, needs to add a resistor on PU-, DR-, FM- ( do not add on + sides );

3. This model of the driver uses a special control circuit, so it matches stepper motor of 6 or 8 outlets only;

4. The driver will automatically stop working when the temperature exceeds 70 degrees, the O.H indicator light normally on, temperature drops to 50 degrees it automatic recovers to work, please install radiator when it's in overheating protection;

5. When the current exceeds rated value or the voltage is lower than rated value, the O.C indicator light normally on, please check the connections and other short troubles needs to re-up power after the faults cleared, or if the power voltage is too low;

6. The PWR green indicator light normally on when the driver is powered on;

7. The TM indicator light comes on when the pulse input go crossing the zero point.

Характеристики
Основні
ВиробникInstar
Країна виробникКитай
Специфікація
Інформація для замовлення
  • Ціна: 1 215 ₴